Vacuum workholding for the Fanuc Robodrill. Machined parallel within 0.1mm. Integrated vacuum, conical locators, and full-table sealing area.
Available for Short Bed, Medium Bed, and Long Bed Robodrills. Bolts to the stock T-slot table. The compact Robodrill enclosure pairs well with the magnetic venturi kit, which mounts to the outside of the machine and keeps the work envelope clear.
The plate doesn’t replace your vise. It expands what the Robodrill can run. Mount it for plate work, sheet metal, large parts, or any job that needs full top-surface access. Pull it off when you need the table back for vise jobs. Or mount your vises on top. The two workflows coexist on the same machine.
$1,237.50
Fits standard Robodrill Alpha-D short bed tables.
Specifically designed to mount directly to a Fanuc Short Bed Robodrill.
This plate is provided with a match machined mounting plate that will ensure easy install.
$3,850.00
Fits Alpha-D long bed tables
Specifically designed to mount directly to a Fanuc Long Bed Robodrill.
This plate is provided with a match machined mounting plate that will ensure easy install.
$2,750.00
Fits Alpha-D medium bed tables
Specifically designed to mount directly to a Fanuc Medium Bed Robodrill.
This plate is provided with a match machined mounting plate that will ensure easy install.
Other Fanuc models – Talk to an engineer for custom requirements on Fanuc machines not listed above.
A typical first install on a Robodrill takes one person about 20 to 30 minutes. The compact bed and clean T-slot pattern make Robodrill installs faster than most larger VMCs. Subsequent installs run 10 to 15 minutes once you’ve done it once.
If your Fanuc Robodrill doesn’t have built-in vacuum, you have two options. The Magnetic Venturi Kit is the right choice for wet machining (flood coolant) since venturis pass fluid through without needing filtration, and it’s the most cost-effective entry. For dry machining or dedicated production, a vacuum pump is more efficient long-term. The plate works with any source pulling 20 inches of mercury or better.
If your Fanuc Robodrill model isn’t in the list above, we’ll design and build a plate for it. Send us your machine model, table dimensions, and the part you’re trying to hold.
Shop the plates above or talk to one of our engineers. We build vacuum fixture plates daily, so we’ve seen your question before.
Common questions about vacuum fixture plates for Fanuc Robodrill Alpha-D machines, including workholding performance, setup, and precision machining considerations.
The best option is a vacuum fixture plate designed for the specific Robodrill table size, whether short, medium, or long bed.
A Fanuc Robodrill vacuum fixture plate mounts directly to the machine table and combines vacuum chuck functionality with a fixture grid. It provides full-surface holding and repeatable positioning for high-precision work.
Robodrill workholding needs to stay stable at high feed rates and tight tolerances. A vacuum fixture plate supports the part across its full bottom surface, which reduces distortion compared to mechanical clamping. It helps maintain flatness and consistency during precision machining.
Cutting force still needs to match the sealed surface area. Light engagement strategies are typically used.
Yes. Vacuum workholding is commonly used for repeat production on Robodrill machines. For recurring parts, setups are typically:
That reduces setup time and supports high-throughput machining.
Plate selection depends on the machine’s table size and travel. Short, medium, and long bed Alpha-D machines have different table dimensions, so the vacuum fixture plate must match the working area and mounting pattern.
Choosing the correct size ensures full coverage and consistent vacuum performance.
A properly set up vacuum fixture plate supports consistent precision. The plate can be faced in-situ to match the machine’s level, and conical locators provide repeatable positioning. Full-surface support helps reduce distortion compared to clamping.
Accuracy depends on the fixture setup and part geometry, not just the vacuum system.
A vacuum fixture plate is used when:
Traditional workholding is still used for heavy cuts or rigid parts that require mechanical clamping.
